Godin *SOLD* Solidac Electric Guitar with Gig Bag - Commission sale *SOLD*

Godin Solidac
The Solidac is all about versatility. The humbucker-single-humbucker pickup design is considered to be the most powerful of commonly used pickup configurations. Add to that the acoustic guitar tones produced by the L.R.Baggs X-Bridge and internal pre-amp and the Solidac could easily become the only guitar you'll ever need.
Specs:

• Mahogany Neck
• Rosewood Fingerboard
• 16" Fingerboard Radius
• 25 1/2" Scale
• 1 11/16" Nut Width
• Silver Leaf Maple Body
• Godin-Design Pickups
• LR Baggs X-Bridge
• Volume Dial - Electric
• Volume Dial - Acoustic
• Tone Dial - Electric
• Magnetic Output
• Acoustic/Mix Output
• Top nut: Tusq by Graphtech
• Nut width: 1 11/16”
• Scale: 25 ½”
• Radius: 16”
• Tuners: High ratio front-loaded locking tuners.
• String Gauge: Godin Nickel electric strings 10-46
• Frets: Medium Nickel
• Pickups: Godin GHN1 (Neck) GS1 (Middle) GHB1 (Bridge)

Flexible Outputs
A look at the bottom of the Solidac reveals two ¼" outputs. The
output closest to the strap pin is a dual function jack. Used on its
own this serves as a mix out carrying the signal from the bridge
transducers as well as that of the magnetic pickups. Separate
volume controls on the guitar make it easy to mix the two signals.
The second ¼" jack carries the signal from the magnetic
pickups on its own. When a jack is plugged into the magnetic
pickup jack the magnetic pickup signal is removed from the mix
output so that there is now a separate signal for each of the pickup
systems.
You can access the Godin pickups by simply plugging your guitar
cable into the first output jack (Output #1). 
The second output jack (Output #2) is an Acoustic/Mix output.
When this output is used by itself it outputs the regular pickups
as well as the acoustic bridge transducers.
If both output jacks are used the signal from the magnetic pickups
is removed from the Acoustic/Mix (Output #2) which now
becomes a dedicated acoustic bridge transducer output. This
feature enables you to separate the pickup output from the
acoustic bridge transducers. This is a convenient way to isolate
the signals by having the pickups output to a guitar amplifier and
the bridge transducer signal output to a P.A. or acoustic guitar
amplifier.

A convenient way of using the Solidac is to run the acoustic
transducer output jack to a volume pedal before going to the PA
or acoustic amp. You can then keep the guitar’s acoustic transducer
volume on at all times and control the output with the vol Output
#2 Output #1

Another option is to use the acoustic tone along with the regular
pickups to create one huge tone.
The Solidac features a separate volume control for the acoustic
bridge with a built in pre-contoured pre-amp for a rich and full
acoustic tone.
By selecting your neck pickup and applying a small amount of
acoustic transducer you can easily achieve a warm sound with
lots of bottom end while maintaining note definition.
The built in active pre-amp for the bridge transducers is powered
by a single 9-volt battery accessible via a small compartment on
the back of the guitar. The pre-amp is activated when the guitar
is plugged in. Therefore, to avoid draining the battery please
make sure to disconnect your cable when the guitar will not be
used for a extended period of time. If the sound of the bridge
transducers begin to sound thin or fuzzy, a battery change is
overdue. Battery life is approximately 300 hours.
The Solidac also features front-loaded locking tuners for easy
string change and better intonation. Simply turn the locking tuner
counter clock-wise to loosen, insert string, tighten the locking
tuner by turning clock-wise and you're done.

Solidac Custom Godin Pickups

Pos. 1 - A,B
Pos. 2 - A,B,C
Pos. 3 - C
Pos. 4 - C,D,E
Pos. 5 - D,E

See images for pickup positions